TITLE

Torque Ripple Minimization of 4 Phase 8/6 Switched Reluctance Motor Drive with Direct Instantaneous Torque Control

AUTHOR(S)
Srinivas, P.; Prasad, P. V. N.
PUB. DATE
December 2011
SOURCE
International Journal on Electrical Engineering & Informatics;Dec2011, Vol. 3 Issue 4, p488
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The switched reluctance motor drives has evolved as an alternative to conventional motors in variable speed drives because of advantages like simple and rugged structure, absence of rotor winding, adaptability to harsh environments like coal mining, high speed operation etc. Because of nonlinearity, torque ripple is high in the motor. This paper presents a high dynamic control technique called Direct Instantaneous Torque Control (DITC) where in the torque is maintained within a hysteresis band by changing the switching states of the phases. Thus torque ripple minimization and fast torque response is an inherent property of DITC. This paper analyses performance of the drive mainly in terms of the torque ripple during acceleration and steady state conditions with DITC in MATLAB/SIMULINK environment and results are discussed elaborately.
ACCESSION #
110872335

 

Related Articles

  • Rusted but not Busted PART 3. AGUILAR, KEVIN // Street Trucks;Jan2015, Vol. 17 Issue 1, p82 

    The article offers step by step instruction for making and installing custom calibrated torque converter.

  • Signal Injection as a Fault Detection Technique. Cusidó, Jordi; Romeral, Luis; Ortega, Juan Antonio; Garcia, Antoni; Riba, Jordi // Sensors (14248220);2011, Vol. 11 Issue 3, p3356 

    Double frequency tests are used for evaluating stator windings and analyzing the temperature. Likewise, signal injection on induction machines is used on sensorless motor control fields to find out the rotor position. Motor Current Signature Analysis (MCSA), which focuses on the spectral...

  • Main Aspects Regarding the Screw-on Torque Diminishing when Using the Fine Pitch Screw. Creiţaru, Adrian // Petroleum - Gas University of Ploiesti Bulletin, Technical Serie;2012, Vol. 64 Issue 2, p71 

    Romanian special standards - according to international (ISO) ones - show metric threads of common use for this kind of screw elements (bolts, nuts); there are a lot of standardized and un-standardized variants and also for any mechanical threaded pieces. In usual practice, the threads are...

  • Low-Speed Hydraulic Pump as a Tool for Setting and Measuring Torque. BANAŚ, Michał // Solid State Phenomena;2014, Vol. 220-221, p969 

    The paper presents a low-speed hydraulic pump which is used in a hydraulic load unit for testing mechanical devices. The control system of the unit reduces an impact of any other hydraulic and mechanical parameters, including temperature and rotational speed, on the torque. The hydraulic load...

  • A direct torque control driven vessel actuator device. Huilue Jiang; Bo Liu; Chuandao Liu // Applied Mechanics & Materials;2014, Issue 651-653, p593 

    Actuator is one of the most important auxiliary mechanisms used to control the ship heading. Focused on the existed shortages of conventional hydraulic driven vessel actuator as complex structure, low efficiency and response etc, by the analysis of torque variation to access the impact of direct...

  • Research of Halbach Array's Influence on Permanent Magnet Synchronous Motor's Performance. Zhang Haoming; Li Hong; PEH Lian Soon // Applied Mechanics & Materials;2014, Issue 651-653, p808 

    The present motors are required to high speed, high efficiency, high power density but low pulsating torque. Traditonal rare-earth permanent magnet motor shows its defect; Halbach Array is a new type of permanent magnet structure: magnet field presents unilateral with the sinusoidal...

  • 5MW Offshore Wind Turbine Control Based on Pitch Joint Torque Controller. Xingjia Yao; Hongfang Xie; Jiangsheng Zhu; Xiaodong Wang; Yingming Liu; Huaiqing Li // Applied Mechanics & Materials;2014, Issue 667-679, p185 

    Modern control theory has been used to design a variable pitch controller based on disturbance accommodating. The controller realizes the optimal control which minimized the controller action and drive-train torque. A torque controller based on pole clustering had been designed to enhance drive...

  • Study on the Static Load Capacity and Synthetic Vector Direct Torque Control of Brushless Doubly Fed Machines. Chaoying Xia; Xiaoxin Hou // Energies (19961073);Nov2016, Vol. 9 Issue 11, p966 

    Compared to the doubly fed machine, the brushless doubly fed machine (BDFM) has high reliability and low maintenance requirements. First, by taking the negative conjugation of the control motor variables in rotor reference frame, a state-space model of BDFM is derived. It is then transformed...

  • Predictive DTC-ISVM for Doubly-Fed Induction Machine System Fed by Indirect Matrix Converter. Aghasi, Majid; Faraji, Vahid; Behnia, Hamid; Khaburi, Davood Arab; Banadaki, Ali Dehghan // International Review on Modelling & Simulations;Apr2012, Vol. 5 Issue 2, p854 

    This paper presents a novel predictive Direct Torque Control (DTC) based on Indirect Space Vector Modulation (ISVM) technique for Doubly-Fed Induction Machine (DFIM) using Indirect Matrix Converter (IMC), which is characterized by a simple structure, minimal torque ripple and constant switching...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics