TITLE

Control Strategy in the Flux Weakening Region of Interior Permanent Magnet Synchronous Machine used in HEV

AUTHOR(S)
Xiaohong Liu; Youtong Zhang
PUB. DATE
June 2014
SOURCE
Applied Mechanics & Materials;2014, Issue 543-547, p1322
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
An new control strategy for interior permanent magnet synchronous machine (IPMSM) which is the most popular motor used in HEV is proposed and investigated, which features is increasing the reference flux weakening voltage to improve efficiency in flux weakening region. Modeling results show that the proposed strategy can achieve the same dynamic and steady state torque performance with higher reference flux weakening voltage, which means higher efficiency.
ACCESSION #
95257960

 

Related Articles

  • Main Aspects Regarding the Screw-on Torque Diminishing when Using the Fine Pitch Screw. Creiţaru, Adrian // Petroleum - Gas University of Ploiesti Bulletin, Technical Serie;2012, Vol. 64 Issue 2, p71 

    Romanian special standards - according to international (ISO) ones - show metric threads of common use for this kind of screw elements (bolts, nuts); there are a lot of standardized and un-standardized variants and also for any mechanical threaded pieces. In usual practice, the threads are...

  • Study on the Static Load Capacity and Synthetic Vector Direct Torque Control of Brushless Doubly Fed Machines. Chaoying Xia; Xiaoxin Hou // Energies (19961073);Nov2016, Vol. 9 Issue 11, p966 

    Compared to the doubly fed machine, the brushless doubly fed machine (BDFM) has high reliability and low maintenance requirements. First, by taking the negative conjugation of the control motor variables in rotor reference frame, a state-space model of BDFM is derived. It is then transformed...

  • Torque ripple reduction PWMs for a single DC source powered dual-inverter fed open-end winding induction motor drive. Sekhar, Kondapalli Ramachandra; Srinivas, Srirama // IET Power Electronics;2018, Vol. 11 Issue 1, p43 

    Two new pulse width modulation (PWM) methods are proposed for a dual two-level inverter (DTLI) fed open-end winding induction motor drive for complete elimination of zero sequence voltage (ZSV), enabling the DTLI drive to be powered from a single DC power supply only. One of the PWM methods is...

  • High-order terminal sliding mode control for brushless doubly-fed machines. Quankun Zhang; Yu Yu; Shuaimei lian; Hong Hu; Yujian Zhang // Applied Mechanics & Materials;2014, Issue 682-686, Special section p384 

    A novel sliding-mode variable structure(SMVS) control strategy is proposed to reduce the ripples of flux and torque of brushless double-fed machines(BDFM) based on direct torque control system. In order to ensure the constant switching frequency for the inverter, two hysteresis regulators in the...

  • Loopshaping of motor torque controller. SIEKLUCKI, GRZEGORZ // Archives of Control Sciences;Jun2013, Vol. 23 Issue 2, p213 

    The controller synthesis problem of the motor torque is presented. The tuning of the II2 controller parameters of the electromagnetic motor torque is introduced. The results are obtained by applying the weighted sensitivity method (nominal performance) which is the optimization in H∞ space....

  • Position Sensorless Direct Torque Control of Brushless DC Motor Drive Using Four-Switch, Three Phase Inverter. Seyedi, S. M.; Halvaei Niasar, A.; Moghbelli, H. // International Review on Modelling & Simulations;Oct2012, Vol. 5 Issue 5, p2036 

    Today, cost reduction is important matter in all of the systems. In brushless dc (BLDC) motor drives, cost reduction can be achieved by elimination of three Hall Effect position sensors and reducing the number of power switches. On the other hand, in order to reduce the torque ripple, direct...

  • Simulation and Analysis of Passive Torque Servo System. Chengcheng Li; Dongxiang Shao; Guanglin Wang // Key Engineering Materials;2016, Vol. 667, p493 

    Passive torque servo system (PTSS) is a key equipment in the hardware-in-the-loop experiment for the test of actuator performance. A novel mathematical model was obtained by analyzing the structure and working conditions of PTSS in this paper and the model was analyzed with the matlab software....

  • Reduction of EMI with Chaotic Space Vector Modulation in Direct Torque Control. Asker, Mehmet Emin; Ozer, Ahmet Bedri; Kurum, Hasan // Electronics & Electrical Engineering;2016, Vol. 22 Issue 1, p40 

    In this paper a study is presented about the reduction of electromagnetic interference (EMI) in Direct Torque Control (DTC) method by the means of chaotic space vector modulation. Space Vector Modulated Direct Torque Control (SV-DTC) is a method developed to reduce current and moment...

  • Duty ratio modulation method to minimise torque and flux linkage ripples for IPMSM DTC system. Tianqing Yuan; Dazhi Wang; Yunlu Li; Sen Tan; Shuai Zhou // Electronics Letters;8/17/2017, Vol. 53 Issue 17, p1188 

    The active vector effects on torque and stator flux linkage are different in direct torque control (DTC) system. These differences may cause the over-compensation or under-compensation to torque and flux linkage leading to large ripples. Aimed at making sure the system can work in an optimum...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics